Sunday 18 May 2014

E60 M-Sport Bumper Retrofit: '08 LCI to '04 SE

I have mentioned hankering after an M-Sport or M5 style front-bumper for my 530d, but they are expensive. A new spurious one will cost about £230, the same price as a damaged genuine one and either of these require painting. A mint one already painted in Titansilver, complete with grilles, parking-sensors and trim will run £400. I've been looking for a few months and this week spotted an undamaged '08 front bumper for £250 with new spot-lamps and grilles, but no sensors or trim. Best of all it was in Wrexham, less than 30 miles away, so when I emailed the seller offering £200 cash on collection and he accepted, I realised that I was now bound to the idea. I got the bumper on in 2 hours, but a lot of bits had to be removed to do it and before I start modifying them to fit I'm sat on a fence between bothering at all, or just going back to stock - I can still get £200 for this M-bumper all day long.


Before you consider doing the retrofit to an SE, I must mention that even if the M-Sport bumper is fully-loaded with trim and bits, you will still need to buy a heap of extra parts to make it fit properly. If you don't, stock parts that get in the way will either have to be binned or modified to fit...

Things that DO fit:
  • Wing and top-grille mounting points.
  • Spot-lamp bulb-holders.
  • Parking-sensors (PDC).
  • Grille-top weather-strip.
Things that do NOT fit:
  • Headlight-washer caps.
  • Headlight-washer cap hinges.
  • Tow-eye cover cap.
  • All 4 lower-grille mounting points.
  • Left + right brake air-duct.
  • Under-tray left + right corners.
  • Front wheel-arch liners.
  • Bumper shock-absorbers (foam-polystyrene blocks).
Assuming your bumper comes bare, you will need these essentials:

H/Light Washer Hinge (Lever) Left [51117896601] (22 in below pic)
H/Light Washer Hinge (Lever) Right [51117896602]
H/Light Washer Cap Left [51117897211] (21 in below pic)
H/Light Washer Cap Right [51117897212]
Tow-eye Cover Cap [51117897210] (9 in below pic)

You can get away with leaving the bumper unbolted in the lower-centre, or easily fab-up some custom brackets, but if you want to buy them then you will need:

Holding Strap [51111973721] (10 in below pic)
2x Adapter Bracket [51117896611] (33 in below pic)

The foam-polystyrene bumper 'shock-absorbers' can be cut to fit or just left off, but if you want them they are:

Shock-absorber Left [51117896589]
Shock-absorber Right [51117896590]

The plastic wheel-arch liners only need a sliver cutting off to make them fit, but if you really want to replace them:

Front Wheel-arch Liner/Cover Left [51717896605]
Front Wheel-arch Liner/Cover Right [51717896606]


The diagram above with all parts can be seen on this page of RealOEM.com.

1 comment:

  1. When your baby changes his/her bed from crib to a toddler bed/child bed, he goes through a transition. In a crib, he/she gets protected from rolling out by the crib bars. For a child bed, this is not possible as there is no bar. But, he might be unable to remove the habit of rolling out at a sudden. Therefore, it can be risky for him as there are chances of falling out of the bed. So, he requires extra security for certain time. To ensure his or her security, you can purchase a set of foam bumpers or bed rails. If you ask for a quality bed bumpers for baby and adults, then we suggest you go for the Hiccapop Toddler Bed Bumper Foam and Bed Rails.

    ReplyDelete